Waterproof and protect your basement, convert a damp basement and cellar into a comfortable dry living space/Keep water out of your basement, your cellar.
The highest water counter pressure resistant and the richest resin based waterproof cementitious tanking system available on the market that will make your waterproofing system last for years!
Waterproof Cement Tanking Systems are a well proven waterproofing solution to render your structures resistant to water counter pressure and infiltration (for basements, cellars and underground room).
Resin Based VS Water Based Waterproofing Cementitious Tanking System:
There are many reasons why professional prefer a resin based waterproofing cementitious tanking system compare to a water based waterproofing cementitious tanking system:
- More resistant with extra last long lasting effect
A Resin based tanking system will last longer than a water based tanking system - Water counter pressure resistant
- Will be more adherent to any masonry surfaces (avoid tanking detachment from the support)
- Easiest application with a smoother product due to our high quality resin properties
- Prefered by professionals in building preservation, building restoration and building renovation
Arcacem Basement and Cellar is a waterproof cementitious tanking system which is highly resistant to hydrostatic pressure whether it is applied from the inside or the outside (pressure from the outside against your building structure).
Arcacem Basement and Cellar works by blocking the capillary pore structure of the concrete surface to liquid water ingress while remaining permeable to water vapour ( which allows any entrapped moisture to escape and the struture to 'breathe').
Penetrating into the pores of the substrate, our waterproof tanking product will become one with your structure (and cannot be pushed off by water pressure).
The waterproof tanking system Arcacem Basement and Cellar does not add heavy weight and additional thickness to your existing structure (3mm) while proving extremely resistant to high hydrostatic pressure.
Advantages:
- Highly resistant to abrasion and erosion
- Convert your damp basement, cellar, underground floor, garage into a living space and increase the value of your property
- Waterproofed basements, garages, cellars can be converted into bathrooms, wine cellars, living rooms, recording studios, nightclubs, bars, restaurants.
- Easy to use and apply
- Very long lasting effect guaranteed!
- Non-toxic
- Provides a waterproof coating which adheres perfectly to damp surfaces, cement and fresh mortar.
- Micro porous and odorless
- Excellent resistance to water counter pressure, negative hydrostatic pressure
- Can be applied horizontally or vertically to the interior or exterior face of the surface on damp substrates
Where to apply?
Arcacem Basement and Cellar waterproof tanking system can be applied to:
- poured concrete,
- reinforced concrete,
- aerated concrete,
- traditional masonry,
- agglomerated masonry blocks,
ARCACEM protects:
- Old and new masonry exteriors (elevated, underground or immerged)
- Cement works subject to salt such as parapets, bridge piles, concrete guide rails, gutters, sidewalks, pavements,
ARCACEM waterproofs:
- Basements, cellars, below-grade construction
- Garage
- Concrete constructions, wall to foundation construction joints
- Top of foundation walls garage walls
- Parking lot structures
Waterproof Cementitious Tanking System Arcacem Basement and Cellar Available Colour:
2 colours are available:
GREY : Resistant to salt water The 25 kg kit of GREY Arcacem Basement and Cellar can be used in agressive environments (mountains, seafront, salt water pools) where salt water or water with a high rate of sulfates is present. Resistance to compression: 52.5
WHITE : The 5 kg kit of WHITE Arcacem Basement and Cellar is not salt water resistant nor is it resistant to water with a high presence of sulfates.Resistance to compression: 32.5
Waterproof Cementitious Tanking System Arcacem Basement and Cellar Pack Sizes:
2 pack sizes: 5kg - 25kg
5kg Kit = 4kg powder + 1 kg resin
25kg = 20kg powder + 5 kg resin
Avoid water based tanking system that are less resistant in regards of water pressure (positive and negative), they are not salt resistant and have a weaker long lasting effect.
Tools
Brush, Trowel, With water immediately after use
Application conditions - Precautions
Do not apply if the surface has cracks or micro cracks.
Do not apply under direct hot sun or on hot surface. In the summer, apply in the morning.
Avoid application if strong wind and/or rain are present.
Do not apply Arcacem Basement and Cellar on frozen substrates or if freezing temperatures are announced within 24 hours.
Surface preparation
Careful attention to the preparation of the surface is essential to guarantee bonding.
The surface must be clean, sound, and free of loose or friable materials.
Where the surface is dry or hot to touch, WET DOWN THE ENTIRE SURFACE BEFORE APPLICATION of the 1st coat only.
IMPORTANT : We highly recommend forming a fillet at the wall to floor junction before applying Arcacem.
This area is one of the most leak-prone areas of basements and the focal point of stress caused by movement and settlement. Concave fillets installed in the wall/floor junction won't eliminate all movement between the wall against the floor, but the stresses are spread over the area of the rounded out fillet, instead of being focused on the point of that 90° angle. Arcacem applies easier and better (no build-up in sharp angles) to the rounded off surface.
Product preparation
Pour the resin into a large container.
Stir in the powder slowly and progressively.
It takes a full minute for the mixture to start bonding (adding ARCACEM from this point on will not pose a mixing problem).
Mix for 2 to 3 minutes, the paste should be of uniform colour, creamy in texture and homogeneous without lumps.
Let it sit a few minutes prior to application.
Use within 2 hours.
Application
We recommend applying the 1st coat with a cement brush.
The brush vibrating movement pushes the Arcacem deep into the substrate.
A trowel application may be done for the to coat if you desire a smoother finish.
Stir material thoroughly before application and periodically during application to maintain a homogeneous mixture throughout the application process.
Apply with a smoothing trowel, brush or roller or project mechanically.
Arcacem Basement and Cellaris applied in 2 coats minimum.
The 1st coat may be reinforced (firmly embedding the reinforcement fibreglass mesh ARCAFIBRE).
The 2nd coat is applied once the 1st has completely hardened (minimum 4 hours in optimal drying conditions).
1st coat : apply with a brush or a smoothing trowel (a brush is better as it creates a massaging effect which causes the product to penetrate deeply into the pores of the substrate). The coat should be approximately 2 to 3mm thick.
Apply a reinforcing fibreglass if necessary
It may not be necessary to reinforce the entire surface but we highly recommend reinforcing the corners, cracks and joints.
2nd coat: Apply Arcacem Basement and Cellar to cover the entire surface, approximately 1 to 2mm thick
3rd coat: If the substrate must resist high counter pressure, (water source near) we recommend a 3rd coat - approximately 1 to 2mm thick.
Wet down the surface for the first coat only not between coats
Finish
Arcacem Basement and Cellar waterproof tanking system can be covered by a concrete screed or slab, tiling or a number of other top coatings.
It is possible to tint Arcacem Basement and Cellar with ARCACOLORS, maximum 3% of total weight. Not recommended for work subject to UV.
Drying Time
Arcacem Basement and Cellar will attain its optimal performance after 28 days drying time. However the following actions may be undertaken sooner:
Light foot traffic dry : 48 hours (at 20°C and 60 % relative humidity)
Between 2 coats: 24 hours
Flling reservoirs - curing time: 12 days
Coverage rate when applying to basements, cellars, underground stuctures:
On smooth surfaces (concrete slab, poured concrete, cement render) :
TOTAL for 2 coats: 3kg per m² (1st coat: 1.5kg per m² - 2nd coat: 1.5kg per m²)
5kg will cover up to: 1.7m²
25kg will cover up to: 8.3m²
On rougher surfaces (brick, cement blocks, stone):
TOTAL for 2 coats: 4kg per m² (1st coat: 2.5kg per m² - 2nd coat: 1.5kg per m²)
5kg will cover up to: 1.3m²
25kg will cover up to: 6.3m²
These quantities might be higher if the leaks are important: in that case an extra coat of 1 or 1.5 kg per m² can be applied.
Store in unopened containers in a clean, dry area.
Keep material from freezing.
