Highest quality direct from factory
Need help ? 020 3151 3120
161,16 £ tax incl.
Arcapoxy Garage is an high resistance, water, oil, grease, acid resistant, epoxy resin paint, for walls and floors in garage, workshop, shop floors. Resists scuffing, fading, cracking, peeling, blistering & hot tire pick-up
Warning: Last items in stock!
Availability date:
ARCAPOXY Garage EPOXY PAINT applies easily to both vertical and horizontal surfaces, indoor and outdoor, to provide a decorative durable coating on walls and floors in areas subject to domestic foot & car traffic.
Arcapoxy Garage EPOXY PAINT can be applied as a protective coating over concrete in:
Arcapoxy Garage EPOXY PAINT has excellent adhesion to a wide variety of surfaces: cement, mortar, brick, stone, wood, metal ...
Arcapoxy Deco EPOXY PAINT has excellent adhesion to a wide variety of surfaces: cement, mortar, brick, stone, wood, metal ...
For kitchen, dinning room, loft, living room, bedroom, basements floors coatings prefer: ARCAPOXY DECO
For factory,public parking, warehouse, stockroom, laboratory, hospital floors coating prefer: ARCAPOXY HEAVY TRAFFIC
* Note:. The displayed colour will depend on your monitor and browser and certain colours cannot be shown adequately. To visualize the actual colour, ask us for our colour card.
0.15kg per sqm per coat - 2 coats= 0.3kg per sqm
For 5kg kit (4.25kg Part A Resin + 0.75Kg Part B Hardener):
Cover up to 32sqm for one coat,
Cover up to 16 sqm for two coats
For 25kg kit (21.25kg Part A Resin + 3.75Kg Part B Hardener):
Cover up to 160 sqm for one coat,
Coover up to 83 sqm for two coats
ARCAPOXY EPOXY PRIMER is recommended before ARCAPOXY GARAGE
* In order to get an high performance coating system that will last at least 5 years please carefully respect datasheet instructions
Arcapoxy Garage is an high resistance, water, oil, grease, acid resistant, epoxy resin paint, for walls and floors in garage, workshop, shop floors. Resists scuffing, fading, cracking, peeling, blistering & hot tire pick-up
Application temperature: between 10° and 25° C
Relative humidity maximum 80%
The temperature must be 3°C superior to the dew point
WOOD:
Degrease and dust well, removing all loose particles and repairing any non-adhesive zones before application. Apply one coat of ARCAPOXY EPOXY PRIMER - 200gr per sqm (m²)
CONCRETE:
Must be 28 days old and free of all laitance. Free water content must be < 4% of the dry mass. Clean with an acid solution to wash off all stains and neutralize the alkalinity of the substrate. Rinse thoroughly leaving no soap or cleaning material suds or residue on the surface. Vacuum the surface once dry.
Note: Very smooth concrete must be cleaned with a hydrochloric acid diluted by 10% to guarantee the penetration of the epoxy paint. Rinse thoroughly after treating and let dry. Application of one coat of ARCAPOXY EPOXY PRIMER - 200gr per sqm (m²) before application is recommended.
METAL:
Degrease and sand blast ferrous metal surfaces Apply one coat of ARCAPOXY EPOXY PRIMER - 200gr per sqm (m²)
TILE:
Degrease, sand lightly in order to give it a texture and open the pores (60 grit sandpaper), removing all loose particles, dust well and repairing any non-adhesive zones before application. Apply one coat of ARCAPOXY EPOXY PRIMER - 200gr per sqm (m²)
ANTI-SLIP:
To render an anti-slipery surface apply 500gr per sqm of silica on the first coat, then brush or vacuum all non adherent silica and then apply the second epoxy garage coat.
Pour the hardener (Part B) steadily into the resin (Part A) and thoroughly mix for 2-3 minutes, preferably by slow speed drill with a paddle attachment until an uniform colour is achieved.
(Never pour directly without mixing, otherwise smoke can appear and the product may be damaged)
You can mix the entire amount or only a part of it depending of how much you need. Remember to always respect/use the ratio: 1 hardener weight to 5.67 resin weigth - 15% hardener to 85% of resin
Apply with a brush, roller, smoothing trowel.
Apply on coat of ARCAPOXY EPOXY PRIMER (200gr per spm)
Apply two coats of ARCAPOXY GARAGE EPOXY PAINT on a completely dry surface
At 20°C allow 24 hours to dry between coats.
Dust free: 4 hours at 20°C, 12 hours at 10°C
Dry to touch: 8 hours at 20°C, 18 hours at 10°C
Recoverable: 18 hours
Allow to cure for a minimum of 24 hours prior to light foot traffic access, 5 days to heavy foot traffic access and 7 days cure at 20°C prior to exposure to chemicals. Lower temperatures will extend the curing time.
1st coat = 0.15 kg per sqm (m²) / 2nd coat= 0.15 kg per sqm (m²)
Total of 0.30kg per sqm (m²) for 2 coats
5 kg kit : cover up to 16 sqm (m²) for 2 coats
Composed of a 4.25kg resin (part A) and a 0.75kg hardener (part B)
25 kg kit: cover up to 83 sqm (m²) for 2 coats
Composed of a 21.25kg resin (part A) and a 3.75kg hardener (part B)
ARCAPOXY EPOXY PRIMER is recommended before ARCAPOXY GARAGE
Store in dry, cool and frost free conditions. Shelf life is 12 months inunopened original packaging.
0.15kg per sqm per coat - 2 coats= 0.3kg per sqm
For 5kg kit (4.25kg Part A Resin + 0.75Kg Part B Hardener):
Cover up to 32sqm for one coat,
Cover up to 16 sqm for two coats
For 25kg kit (21.25kg Part A Resin + 3.75Kg Part B Hardener):
Cover up to 160 sqm for one coat,
Coover up to 83 sqm for two coats
ARCAPOXY EPOXY PRIMER is recommended before ARCAPOXY GARAGE
We did not upload photos or articles for this item
Quick Delivery
Departure from French Manufacturer within 24 hours (excepted for custom colours) Delivery time within 5-7 days
Secure Payment
All your transactions are 100% secure and safe
Direct Price from our Factory
No intermediary, cheapest prices for highest quality.
Need Help?
We are available to answer your questions on:
020 3151 3120 or by mail: contact@arcane-industries.co.uk